HWg-PowerEgg: 230V power detection and switching

Temperature sensor controls 230V switch

PowerEgg controlled by temperature sensor Detects and controls 230V

PowerEgg combines two functions in one device -power Detector & Control. Detector indicate failures of electricity supply (110/230V, single phase) by relay output. Power Control can switch Off/On power supply output 8A, it's controlled with a low voltage input. The PowerEgg can be connected to any device with digital inputs (DI) and digital outputs (DO).

The PowerEgg combines two functions in one device:

1) Detector: Detects voltage, its presence is indicated with a relay output (electrically isolated).
2) Control: Controls an output electricity socket, max. 8A.

PowerEgg, together with e.g. Poseidon 3266 or Damocles MINI, can be used to monitor the presence of the line voltage. PowerEgg can disconnect its output with a relay contact; this can be used to remotely switch an additional cooling, fan, light, or sirene. Both functions are electrically isolated, and can be connected to any dry contact input or a relay output.

DETECTOR Input: Voltage detection (110/230V) - IEC-320 C14
DETECTOR interface: Connect to any dry contact DI (digital input)
CONTROL Output: Turns on/off the 110/230V output voltage (max 8A) – can be connected to any digital output - IEC-320 C13
CONTROL interface: Connect to any DO (digital output) - relay or open collector
Compatible with: Poseidon2, Damocles2, I/O controller, HWg-Ares, HWg-STE2


HWg-Power Detector: 230V power detection with relay output

HWg-Power Detector

230V detector Connect to HWg-STE2, Poseidon2, Ares and sends alarm

Voltage failure detector 110/230V (single phase) which can be connected directly to the wall socket. Galvanic insulated relay output (NO) can be connected to a digital input (DI) of any HW group product.

Power Detector detects the presence of voltage which it signals on its relay output (galvanic insulated). Power Detector can be connected to Digital Input (DI) of HWg-STE2, Poseidon2, Damocles2, and Ares and detects the voltage presence on any wall socket. From these devices, an alarm can be sent by e-mail, SNMP, or SMS. E.g. the UPS input can be monitored to prevent failures.

The relay output is NO type, the closed status signalizes the presence of 110-230V voltage. A load of up to 50V/130mA and resistivity of up to 10 Ohm can be connected to the relay output.

Input:
Voltage detection 110/230V (Type A, Type C, Type G)
Output: Relay output NO (max 50V / 130V / max 10 Ohm)

HWg-Light-1Wire sensor

Requests and orders: Send E-Mail to insinova@insinova.ch

Light sensor Simple light intensity sensor for indoor use.

Simple light intensity sensor for indoor use. The sensor is designed for use with Poseidon, Ares and other HW group products.

A typical application is to distinguish day and night, or to detect presence of people in a server room (light turned on).

Environment: Indoor use
Output: 0 – 100%
Cable length: 3m
Interface: 1-Wire UNI (RJ11)

HWg-Temp-1Wire 1m / 3m / 10m sensor

Requests and orders: Send E-Mail to insinova@insinova.ch

Temperature sensor

Temperature sensor for IT and production environment.

Environment: Indoor use
Input temperature range: -10°C to +80°C
Accuracy: ± 0.5 °C (25°C)
Cable length: 1m / 3m / 10m
Interface: 1-Wire UNI (RJ11)

HWg-Temp-1Wire-FLAT 3m sensor

Requests and orders: Send E-Mail to insinova@insinova.ch

Temperature sensor for freezers with flat cable

Temperature sensor, -30°C to +60°C (-22°F to +140°F), for freezer and outdoor use. The sensor in a stainless steel tube is safe to use even in pharmaceutical or food industry.

Suitable for installation in a refrigerator, the flat cable can be laid under the door seal, no need to drill into the refrigerator.

Environment: Refrigerator / indoor use, sensing element in a stainless steel tube, waterproof (IP67, 17240 stainless steel probe - Ø5.7mm)
Input temperature range: -30°C to +60°C
Accuracy: ± 0.5 °C (25°C)
Cable length: 3m
Interface: 1-Wire UNI (RJ11)

HWg-Temp-1Wire-Outdoor 3m sensor

Requests and orders: Send E-Mail to insinova@insinova.ch

Outdoor temperature sensor

Temperature probe, -50°C to +125°C for outdoor usage. The probe in a stainless steel tube is safe to use even in pharmaceutical or food industry.

Environment: Indoor or outdoor use. Sensing element in a stainless steel tube, waterproof, silicon cable (IP67, 17240 stainless steel probe - Ø5.7mm)
Input temperature range: -50°C to +125°C
Accuracy: ± 0.5 °C (25°C)
Cable length: 3m
Interface: 1-Wire UNI (RJ11)

HWg-Humid-1Wire 1m / 3m / 10m sensor

Requests and orders: Send E-Mail to insinova@insinova.ch

Humidity sensor

Humidity sensor for IT and production environment.

Environment: Indoor use
Input humidity range: 0% to 100% RH (relative humidity)
Accuracy: ± 2% RH (25°C)
Cable length: 1m / 3m / 10m
Interface: 1-Wire UNI (RJ11)

HWg-HTemp-1Wire 3m sensor

Requests and orders: Send E-Mail to insinova@insinova.ch

Combined Humidity & Temperature sensor

Combined humidity and temperature sensor for IT and production environment.

Environment: Indoor use
Input temperature range: -30°C to +85°C
Input humidity range: 0% to 100% RH (relative humidity)
Accuracy: ± 0.5 °C (25°C), ± 2% RH (25°C)
Cable length: 3m
Interface: 1-Wire UNI (RJ11)

HWg-HTemp-1Wire Rack19

Requests and orders: Send E-Mail to insinova@insinova.ch

Combined Humidity & Temperature sensor for 19" rack

Combined temperature and humidity sensor for IT environment. Fits into a 19" or 10" cabinet (1U size).

Environment: Indoor use
Input temperature range: -10°C to +80°C
Input humidity range: 0% to 100% RH (relative humidity)
Accuracy: ± 0.5 °C (25°C), ± 2% RH (25°C)
Cable length: 3m
Interface: 1-Wire UNI (2 x RJ11, can be daisy-chained)

HWg-HTemp-1Wire Outdoor 3m

Requests and orders: Send E-Mail to insinova@insinova.ch

Combined Humidity & Temperature sensor for outdoor usage

Combined temperature and humidity sensor for outdoor usage

Environment: Indoor and outdoor use
Input temperature range: -30°C to +85°C
Input humidity range: 0% to 100% RH (relative humidity)
Accuracy: ± 0.5 °C (25°C), ± 2% RH (25°C)
Cable length: 3m
Interface: 1-Wire UNI (RJ11)

HWg-HTemp-1Wire Box2

Requests and orders: Send E-Mail to insinova@insinova.ch

Combined Humidity & Temperature sensor in a box for wall mount

Combined temperature and humidity sensor for indoor use, wall mount.

Environment: Indoor use, wall mount
Input temperature range: -10°C to +80°C
Input humidity range: 0% to 100% RH (relative humidity)
Accuracy: ± 0.5 °C (25°C), ± 2% RH (25°C)
Cable length: 3m
Interface: 1-Wire UNI (2 x RJ11, can be daisy-chained)

HWg-Temp-485 Box2

Requests and orders: Send E-Mail to insinova@insinova.ch

Temperature Sensor for RS-485

Temperature probe for indoor use. Communicates over the RS-485 bus using a simple communication protocol. Designed for Poseidon units.

Sensors can be daisy-chained
Sensorscan be connected to a “star” topology using patch cables and an S-Hub unit


Environment: Indoor use, wall mount
Input temperature range: -10°C to +70°C
Accuracy: ± 0.5 °C (25°C)
Interface: RS-485, RJ45 + terminals
Compatible with: Poseidon 2250


HWg-HTemp-485 Box2

Requests and orders: Send E-Mail to insinova@insinova.ch

Combined Humidity & Temperature sensor in a box for wall mount

Combined temperature and humidity sensor for indoor use, wall mount. Communicates over the RS-485 bus using a simple communication protocol. Designed for Poseidon units.

Sensors can be daisy-chained
Sensorscan be connected to a “star” topology using patch cables and an S-Hub unit


Environment: Indoor use, wall mount
Input temperature range: -10°C to +70°C
Input humidity range: 0% to 100% RH (relative humidity)
Accuracy: ± 0.75 °C (25°C), ± 4% RH (25°C)
Interface: RS-485, RJ45 + terminals
Compatible with: Poseidon 2250


HWg-Poseidon S-Hub

Requests and orders: Send E-Mail to insinova@insinova.ch

S-Hub to connect RS-485 sensors

Hub to connect several RS-485 sensors to a Poseidon 2250 unit. The bus uses CAT5 cabling and RJ45 jacks.

Allows connecting up to 8 RS-485 sensors into a “star” topology
S-Hub can be daisy-chained

Environment: Indoor use
Input: Poseidon 2250
Interface: RS-485, RJ45
Power supply: Powered over RS-485 Cat5 cable from a Poseidon unit, connector for extra power supply (jack for wall plug adaptor)


HWg-Spider

Requests and orders: Send E-Mail to insinova@insinova.ch

Spider connects 1-Wire sensors to RS-485 bus

Spider enables connecting four 1-Wire sensors (temperature, humidity) or contacts to the RS-485 bus. Up to six Spiders (24 sensors) can be connected to a single Poseidon 2250.

Spider simplifies large-scale installations. RS-485 uses CAT5 cabling with RJ45 jacks and achieves the longest distances. Typical applications include connecting temperature sensors, humidity sensors or door contacts for several refrigerators in the middle of the RS-485 bus.

Typical applications include monitoring clusters of refrigerators in a supermarket. One CAT5 cable connects a cluster of 4 freezers. Each freezer contains a 1-Wire FLAT sensor connected to the Spider. Individual clusters can be daisy-chained.

Environment: Indoor use
Input: 4x 1-Wire RJ11 probes (temperature / humidity) or contacts
Connects to: Poseidon 2250
Interface: RS-485, RJ45
Power supply: Powered over RS-485 Cat5 cable from a Poseidon unit, connector for extra power supply (jack for wall plug adaptor)

HWg-100A (30A) DC Current probe 1W-UNI

Sensor for up to 100A current measurement

100A (30A) DC Current probe 1W-UNI can measure DC current of up to 100A (30A) using a shunt. The shunt is connected directly into the measured circuit. The sensor is suitable for monitoring the power input of Telco cabinets or UPS, or for monitoring battery charging. Together with a Poseidon2 or HWg-Ares unit, it can serve as an early warning system in case of overload or current direction change (charge/discharge). 100A (30A) DC Current probe 1W-UNI consists of a shunt and a 1-Wire converter.

Input: DC current from 0.1A to 100.0A (0.1A to 30.0A)
Output (interface): 1-Wire UNI (2x RJ11 for daisy-chaining)
Electrical isolation: Yes
Cable length between the shunt and the converter: 1m
Connects to: Poseidon 2, Ares
Measured voltage: max. 60V
Power: Bus-powered (1-Wire UNI) – max. 2 sensors per active port
Environment: Indoor use



HWg-Sens-485-UI

Requests and orders: Send E-Mail to insinova@insinova.ch

Sensor for measuring voltage and current

Sensor for measuring voltage and current. Connects to the RS-485 bus, fits on a DIN rail. Sens-UI features two independent inputs (Ch1, Ch2). Each input can be configured to measure current or voltage.

Environment: Indoor use, DIN rail
Inputs: 2 electrically isolated channels, Ch1 and Ch2
Configuration of inputs: Specified by the ordering number, configurable over RS-485
Input voltage range: 0..15 VDC (0.1V resolution)
Input current range: 0..25mA DC (0.1 mA resolution)
Operating temperature: The converter works from -25 to +70°C
Interface: RS-485, terminals
Compatible with: Poseidon 2250
Power supply: From the Poseidon (12V), or 8..28VDC




HWg-Temp-485-Pt100 "Box"

Requests and orders: Send E-Mail to insinova@insinova.ch

Pt100 industrial temperature sensor

Very durable, industrial temperature sensor. -20°C to +80°C (-4°F to +176°F), IP67, wall mount. A Pt100/A probe is in the tip of the tube. Communicates over the RS-485 bus using a simple communication protocol. Designed for Poseidon units.

Typical applications include measuring temperature in places that can be flooded with water, or in environments with significant water condensation.

Environment: Indoor or outdoor use – IP67, wall mount
Input temperature range: -25°C to +80°C, accuracy ±0.2°C (Pt100 sensing element)
Interface: RS-485, terminals
Compatible with: Poseidon 2250
Power supply: From the Poseidon (12V), or 8..28VDC




HWg-Temp-485-2xPt100 "DIN"

Requests and orders: Send E-Mail to insinova@insinova.ch

2 x Pt100 temperature sensor

Sensor for measuring temperature using two external Pt100 probes. The external probes can contain Pt100 or Pt1000 (temperature range of -55°C to +200°C, ±0.15°C). Fits on a DIN rail.

Note: Temperature sensors (e.g. Temp-485-Pt100 “Cable”) are sold separately.

Environment: Indoor use, DIN rail
Inputs: 2 channels for connecting Pt100 or Pt1000 probes
Input range: Probe temperatures from -55°C to +200°C / ±0.15°C
Probe connection: External probe, 2 or 3 wires
Operating temperature: The converter works from -25 to +80°C
Interface: RS-485, terminals
Compatible with: Poseidon 2250
Power supply: From the Poseidon (12V), or 8..28VDC







HWg-Temp-485-Pt100 "Cable"

Requests and orders: Send E-Mail to insinova@insinova.ch

Pt100 temperatur sensor cable

Sensor for measuring temperature using an external Pt100 probe (included). The external Pt100 probe comes with a 2m cable.
The converter is built into a wall-mountable, IP67 box.

Environment: Indoor or outdoor use – IP67, wall mount
Input: 1 channel for connecting a Pt100 or Pt1000 probe
Supplied probe: External PT30 probe (stainless steel, 2m silicon cable)
Temperature range of the supplied probe: -55°C to +200°C, accuracy ±0.2°C (Pt100)
Operating temperature: The converter works from -25 to +80°C
Interface: RS-485, terminals
Compatible with: Poseidon 2250
Power supply: From the Poseidon (12V), or 8..28VDC


HWg-Temp-485-Pt100 "Frost"

Requests and orders: Send E-Mail to insinova@insinova.ch

Temperature sensor for -190°C to +200°C

Temperature sensor for very low temperatures. The probe in a stainless steel housing measures temperatures from -190°C to +200°C, accuracy ±0.2°C (Pt100).

The RS-485 converter is built into a wall-mountable, IP67 box. Operating temperature is -25°C to +80°C.

Typical applications include temperature measurement in the pharmaceutical industry or freezing plants.

Environment: Indoor or outdoor use – IP67, wall mount
Supplied probe: External Pt100 sensor for low temperatures (stainless steel housing, 2m cable)
Temperature range of the supplied probe: -190°C to +200°C, accuracy ±0.2°C (Pt100)
Operating temperature: The converter works from -25 to +80°C
Interface: RS-485, terminals
Compatible with: Poseidon 2250
Power supply: From the Poseidon (12V), or 8..28VDC


HWg-Temp-485 T3419: RS-485 temperature & humidity sensor with display

Requests and orders: Send E-Mail to insinova@insinova.ch

Temperature & humidity sensor with display

Industrial temperature and humidity sensor with a LCD display. Designed for indoor or outdoor use. The probe is mounted on a 1m cable. Wall mount, connects to a Poseidon unit over RS-485.

Typical applications include environment monitoring in rooms where immediate display of measured values is an advantage.

Environment: Indoor or outdoor use – IP65, wall mount
Temperature: -30°C to +105°C, accuracy ±0.4°C
Humidity: 0% to 100 % RH, accuracy ±2,5°C (5% to 95% / 23 °C)
Dew point measurement: Yes
Interface: RS-485, terminals
Compatible with: Poseidon 2250
Power supply: From the Poseidon (12V), or 8..28VDC


HWg-Temp-485 T7410: Pressure, temperature & humidity sensor with display

Requests and orders: Send E-Mail to insinova@insinova.ch

Pressure humidity temperature sensor with display

Atmospheric pressure, temperature and humidity sensor with a LCD display. Designed for indoor or outdoor use. Wall mount, connects to a Poseidon unit over RS-485.

Typical applications include environment monitoring in the pharmaceutical industry and in rooms where immediate display of measured values is an advantage.

Environment: Indoor or outdoor use – IP65, wall mount
Temperature: -30°C to +85°C, accuracy ±0.4°C
Humidity: 0% to 100 % RH, accuracy ±2,5°C (5% to 95% / 23 °C)
Dew point measurement: Yes
Atmospheric pressure: 600 to 1100hPa, ±1.3hPa at 23°C
Interface: RS-485, terminals
Compatible with: Poseidon 2250
Power supply: From the Poseidon (12V), or 8..28VDC